jitsbuild-platform
|
jitsbuild-platform [2013/05/20 07:43] buildrob |
jitsbuild-platform [2014/01/25 17:35] (current) jit |
||
|---|---|---|---|
| Line 2: | Line 2: | ||
| [[jitsbuild-x-axis|Prev: x-axis]] < [[jitsbuild| Up to Jitsbuild]] > [[jitsbuild-extruder|Next: Extruder]] | [[jitsbuild-x-axis|Prev: x-axis]] < [[jitsbuild| Up to Jitsbuild]] > [[jitsbuild-extruder|Next: Extruder]] | ||
| + | |||
| + | //This page pertains to the Bukobot v1. Some portions may be useful to v2 owners. For more information, see [[jitsbuild|here]].// | ||
| Shown here is the 8" heated platform. The other types of platform assemble in a similar way. | Shown here is the 8" heated platform. The other types of platform assemble in a similar way. | ||
| Line 34: | Line 36: | ||
| In particular, ensure that the white thermistor cable does not move at all at the point where it is soldered onto the platform (as the platform moves backwards and forwards) otherwise the connection will fail sooner or later at this point. Hence the use of a zip tie in the above picture. | In particular, ensure that the white thermistor cable does not move at all at the point where it is soldered onto the platform (as the platform moves backwards and forwards) otherwise the connection will fail sooner or later at this point. Hence the use of a zip tie in the above picture. | ||
| + | |||
| + | Other warnings: ensure that the you put some tape over the top and bottom of the +ve (+12V) heated bed terminal and over the underside of the heated bed LED and resistor (if either thermistor wire or a grounded wire touches these points then it will permanently damage the Arduino board), also ensure that the -ve terminal does not touch the resistor next to the -ve terminal or it will also damage the LED on the heated bed. | ||
| While you're here, look inside the little hole in the middle of the heated bed: | While you're here, look inside the little hole in the middle of the heated bed: | ||
| Line 129: | Line 133: | ||
| Mount the glass on the platform. | Mount the glass on the platform. | ||
| + | |||
| + | Also, see [[http://forum.bukobot.com/index.php?topic=3071.msg4628#msg4628|this]]. | ||
| [[jitsbuild-x-axis|Prev: x-axis]] < [[jitsbuild| Up to Jitsbuild]] > [[jitsbuild-extruder|Next: Extruder]] | [[jitsbuild-x-axis|Prev: x-axis]] < [[jitsbuild| Up to Jitsbuild]] > [[jitsbuild-extruder|Next: Extruder]] | ||
| //The contents of this page may be re-used under any of the following licenses: The [[http://creativecommons.org/licenses/by-sa/3.0/|Creative Commons Attribution-ShareAlike 3.0 Unported License (CC BY-SA 3.0)]], or the [[http://www.gnu.org/copyleft/fdl.html|GNU Free Documentation License (GFDL, version 1.2 or later)]]. Nothing on any of these pages is there to tell you what to do, only what other people have already done.// | //The contents of this page may be re-used under any of the following licenses: The [[http://creativecommons.org/licenses/by-sa/3.0/|Creative Commons Attribution-ShareAlike 3.0 Unported License (CC BY-SA 3.0)]], or the [[http://www.gnu.org/copyleft/fdl.html|GNU Free Documentation License (GFDL, version 1.2 or later)]]. Nothing on any of these pages is there to tell you what to do, only what other people have already done.// | ||
jitsbuild-platform.1369053799.txt.gz · Last modified: 2013/05/20 07:43 by buildrob
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 3.0 Unported
