jitsbuild-x-leftend
|
jitsbuild-x-leftend [2012/12/14 15:44] jit |
jitsbuild-x-leftend [2014/01/25 17:38] (current) jit |
||
|---|---|---|---|
| Line 2: | Line 2: | ||
| [[jitsbuild-x-carriage|Prev: X carriage]] < [[jitsbuild| Up to Jitsbuild]] > [[jitsbuild-x-rightend|Next: X right end]] | [[jitsbuild-x-carriage|Prev: X carriage]] < [[jitsbuild| Up to Jitsbuild]] > [[jitsbuild-x-rightend|Next: X right end]] | ||
| + | |||
| + | //This page pertains to the Bukobot v1. Some portions may be useful to v2 owners. For more information, see [[jitsbuild|here]].// | ||
| =====Parts===== | =====Parts===== | ||
| Line 11: | Line 13: | ||
| =====Clean Part===== | =====Clean Part===== | ||
| - | The printed plastic part shown in this image has a significant overhang in the large circular opening (this is the opening on the underside where the UHMW nut, the white object at lower left, will be inserted). The printing technique used to make this part cannot produce a sharp clean profile with this kind of overhang, so the part must be trimmed before you attach parts to it. The trimming and clean up of this opening is non-trivial. It can take some work and some time. A 1/4 sharp wood chisel and a X-ACTO knife help a lot. Larger material will crack and break away, the smaller bits of plastic deeper in the circular opening can be cut and scraped away with the 1/4 wood chisel. Just make sure you don't poke a tool through the hole and cut your hand holding it on the other side. If there is concern about how much material is to be removed, consider the fact that the UHMW nut should be sitting flat against the bottom of the opening, so if there are chunks that prevent this then they need to be removed. | + | The printed plastic part shown in this image has a significant overhang in the large circular opening (this is the opening on the underside where the UHMW nut, the white object at lower left, will be inserted). The printing technique used to make this part cannot produce a sharp clean profile with this kind of overhang, so the part must be trimmed before you attach parts to it. The trimming and clean up of this opening is non-trivial. It can take some work and some time. A 1/4" (6mm) sharp wood chisel and a X-ACTO knife help a lot. Larger material will crack and break away, the smaller bits of plastic deeper in the circular opening can be cut and scraped away with the 1/4 wood chisel. Just make sure you don't poke a tool through the hole and cut your hand holding it on the other side. If there is concern about how much material is to be removed, consider the fact that the UHMW nut should be sitting flat against the bottom of the opening, so if there are chunks that prevent this then they need to be removed. |
| Note, however, that you don't have to make the bottom surface of the UHMW nut flush with the bottom of the X end block. Some people do this so that the machine looks nicer, but it's not really important to the function of the printer. What's most important is that the UHMW nut is level, and doesn't shift around. So try to make that rough printed surface reasonably level and flat. If it was really important that the nut fit precisely and completely into that hollow, the parts would have been designed differently so that the nut fit that way right out of the box. Deezmaker never intended you to engage in hard manual labor with sharp instruments just to fit the kit together. | Note, however, that you don't have to make the bottom surface of the UHMW nut flush with the bottom of the X end block. Some people do this so that the machine looks nicer, but it's not really important to the function of the printer. What's most important is that the UHMW nut is level, and doesn't shift around. So try to make that rough printed surface reasonably level and flat. If it was really important that the nut fit precisely and completely into that hollow, the parts would have been designed differently so that the nut fit that way right out of the box. Deezmaker never intended you to engage in hard manual labor with sharp instruments just to fit the kit together. | ||
| Line 17: | Line 19: | ||
| //whosawhatsis says:// | //whosawhatsis says:// | ||
| > I punch out the bridge and then run my pocket knife along the inner edge of the circle around where the nut goes to taper it and allow the nut to slide in a big easier, but that's it. The underside of the UHMW nut trap should not need any additional cleaning. | > I punch out the bridge and then run my pocket knife along the inner edge of the circle around where the nut goes to taper it and allow the nut to slide in a big easier, but that's it. The underside of the UHMW nut trap should not need any additional cleaning. | ||
| + | |||
| + | //ncorison says:// | ||
| + | >I used a 5/8" deep well automotive socket lined with emery cloth to flatten the bottom surface and clean up the sides and a smaller one to clean up the sides of the top hole. | ||
| {{:wiki:jitsbuild:cleanup1.png?800}} | {{:wiki:jitsbuild:cleanup1.png?800}} | ||
| Line 31: | Line 36: | ||
| (Some other parts seen in this image will be added later.) | (Some other parts seen in this image will be added later.) | ||
| + | |||
| + | Note that the attachment screw for the UHMW nut is there primarily to keep the nut from rotating in its holder. Don't tighten it so much that you can't pop the nut out of its holder with your thumb. If something goes wrong and the printer tries to drive the X axis down into an obstacle, the UHMW nuts should pop out to prevent further damage. | ||
| Check that there are no protuberances in the channels that will hold the long steel rods. Get out a steel rod and check that it fits snugly into these channels. It needs to rest on the bottom of the channel. See [[Cleaning up printed parts]]. | Check that there are no protuberances in the channels that will hold the long steel rods. Get out a steel rod and check that it fits snugly into these channels. It needs to rest on the bottom of the channel. See [[Cleaning up printed parts]]. | ||
| Line 54: | Line 61: | ||
| {{:wiki:jitsbuild:x-leftend_assembled_bottomview.png?800}} | {{:wiki:jitsbuild:x-leftend_assembled_bottomview.png?800}} | ||
| - | Note that the two nuts near the bottom of this image are sitting on top of nut-shaped depressions, but don't fit precisely into them. They don't need to. There is room on the bottom of this part for the nuts to protrude from the surface. Threadlocker can be used later to keep these nuts from wandering if you are concerned about it. | + | Note that the two M2.5 nuts near the bottom of this image are sitting on top of nut-shaped depressions, but may not fit precisely into them. They don't need to. There is room on the bottom of this part for the nuts to protrude from the surface. Threadlocker can be used later to keep these nuts from wandering if you are concerned about it. An M3 washer should be threaded on the top side of each of these M2.5 x 16mm screws (the washer is screwed down against the steel rod going through the channel to hold it in place). |
| (Almost) top view: | (Almost) top view: | ||
| Line 66: | Line 73: | ||
| =====End Stop===== | =====End Stop===== | ||
| - | Next we will install the endstop. However, you may not want to install yours yet, as it tends to be in the way and the wires can be easily broken. You may wish to follow these steps to attach the endstop switch to its holder, and wait until final assembly of the printer before attaching this subassembly to the X left end. Many of the images from this point on will show the endstop already installed. | + | In this section we describe how to install the X-axis endstop; however, you may not want to install yours now as it tends to be in the way and the wires can be easily broken. Instead you can wait until final assembly of the printer before attaching this subassembly to the X left end. Many of the images from this point on will however show the endstop already installed. |
| From the endstops kit ([[bukobot-parts-list#endstops|bag 5]]): | From the endstops kit ([[bukobot-parts-list#endstops|bag 5]]): | ||
| Line 74: | Line 81: | ||
| {{:wiki:jitsbuild:x-endstop.png?800}} | {{:wiki:jitsbuild:x-endstop.png?800}} | ||
| - | Some builders have positioned the switch on the other side of its printed bracket. It should work either way. This way places the wires in a more protected position. | + | Some builders have positioned the switch on the other side of its printed bracket. It should work either way; however, the depicted orientation places the wires in a more protected position and the end-stop switch is triggered by hitting the side of the front-left bearing holder rather than trying to catch the aluminum plate edge (this means that the importance of the endstop up/down position is far less). |
| - | Check to make sure stray strands of wire aren't shorting across the switch terminals. | + | Check to make sure stray strands of wire aren't shorting across the switch terminals. Also one mounting hole of the endstop microswitch is smaller than the other. The smaller hole can be drilled out with a 2.5mm drill so that the screw easily passes through it. |
| Thread the endstop wires through the same oval hole near the motor, wrap all the wires around the assembly, and set it aside, along with its Z-slide sub-kit. | Thread the endstop wires through the same oval hole near the motor, wrap all the wires around the assembly, and set it aside, along with its Z-slide sub-kit. | ||
jitsbuild-x-leftend.1355521465.txt.gz · Last modified: 2012/12/14 15:44 by jit
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 3.0 Unported
