host-slicing-settings
|
host-slicing-settings [2013/08/04 19:43] deezmaker |
host-slicing-settings [2014/04/16 16:06] (current) whosawhatsis |
||
|---|---|---|---|
| Line 5: | Line 5: | ||
| === Slic3r profiles to get started === | === Slic3r profiles to get started === | ||
| - | [[{:bukobotv2:bukobot-vanilla_-_no-platform_3.jpg?100|width:300px}http://bukobot.com/_media:software:buko_v2_slic3r_profiles.zip|Bukobot v2 Slic3r profiles]] | + | [[{:bukobotv2:bukobot-vanilla_-_no-platform_3.jpg?100|width:300px}http://bukobot.com/_media/software:buko_v2_slic3r_profiles_2013-07.zip|Bukobot v2 Slic3r profiles]] |
| - | [[{:bukito:bukito_prototype.jpg?133|width:300px}http://bukobot.com/_media:software:bukobot_profiles.zip|Bukito Slic3r profiles]] | + | [[{:bukito:bukito_prototype.jpg?133|width:300px}http://bukobot.com/_media/software:bukito_slic3r_profiles_2014-01.zip|Bukito Slic3r profiles]] |
| [[{:buko-8-vanilla-01.jpg?100|width:220px}http://bukobot.com/_media/software:bukobot_profiles_v1.zip|Bukobot v1 Slic3r profiles]] | [[{:buko-8-vanilla-01.jpg?100|width:220px}http://bukobot.com/_media/software:bukobot_profiles_v1.zip|Bukobot v1 Slic3r profiles]] | ||
| Line 26: | Line 26: | ||
| * Compatibility: Reprap 5D / Marlin / Sprinter **(250,000 Baud)** | * Compatibility: Reprap 5D / Marlin / Sprinter **(250,000 Baud)** | ||
| - | * Nozzle Diameter: 3mm Filament / 0.35mm extrusion hole | + | * Nozzle Diameter: 3mm Filament / 0.35mm extrusion hole for Bukobots, 1.75mm Filament / 0.5mm extrusion hole for Bukito |
| - | * Extruders: 1 for all Bukobots except for the Bukobot 8 Duo which has 2 | + | * Extruders: 1 for all except for the Bukobot 8 Duo which has 2 |
| - | * X & Y Steps using 15 teeth / 3.18 pitch synchromesh cable 55.99/mm | + | * X & Y Steps using 15 teeth / 3.18 pitch synchromesh cable 111.98/mm at 1/32 microstepping |
| - | * Z Steps for M6 threaded rods: 3200 | + | * Z Steps for M6 threaded rods: 6400/mm at 1/32 microstepping |
| - | * Extruder Steps using Tatsu Drive Gear and 13.6:1 ratio stepper motor: 1260/mm | + | * Extruder Steps using Tatsu Drive Gear and 13.6:1 ratio stepper motor (Bukobot): 630/mm at 1/8 microstepping |
| - | * X/Y Travel Speed: 100-200mm/sec (150mm/sec recommended) | + | * Extruder Steps using Tatsu Drive Gear and direct-drive stepper motor (Bukito): 185.2/mm at 1/32 microstepping |
| + | * X/Y Travel Speed: 100-355mm/sec (150mm/sec recommended) | ||
| * X/Y Extruding Speeds: Max about 200mm/sec (tested), (100mm/sec average recommended) | * X/Y Extruding Speeds: Max about 200mm/sec (tested), (100mm/sec average recommended) | ||
| - | * Extruder Retract Speed: 25mm/minute or less (20mm recommended) | + | * Extruder Retract Speed: 25mm/sec or less (20mm recommended) |
| * Z axis speed: 250mm/minute (4mm/sec) or less (200mm/minute recommended) | * Z axis speed: 250mm/minute (4mm/sec) or less (200mm/minute recommended) | ||
| - | * Build Volume: 200mm X 200mm X 200mm (8" inches cube) | + | * Bukobot Build Volume: 200mm X 200mm X 200mm (8" inches cube), platform center: X:100mm, Y:100mm |
| - | * Center of platform: X=100mm, Y=100mm | + | * Bukito Build Volume: 125mm X 150mm X 125mm (5"x6"x5" inches cube), platform center: X:62.5mm, Y:150mm |
| ===== Repetier-Host Settings ====== | ===== Repetier-Host Settings ====== | ||
host-slicing-settings.1375663392.txt.gz · Last modified: 2013/08/04 19:43 by deezmaker
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 3.0 Unported
