jitsbuild-x-rightend
|
jitsbuild-x-rightend [2012/12/04 16:24] jit |
jitsbuild-x-rightend [2014/01/25 17:39] (current) jit |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| - | ===jit's build: X right end=== | + | ======jit's build: X right end======= |
| - | (Go back up to [[jitsbuild|jit's build]]) | + | [[jitsbuild-x-leftend|Prev: X left end]] < [[jitsbuild| Up to Jitsbuild]] > [[jitsbuild-y-backend|Next: Y back end]] |
| - | Parts in bag 16. | + | //This page pertains to the Bukobot v1. Some portions may be useful to v2 owners. For more information, see [[jitsbuild|here]].// |
| + | |||
| + | =====Parts===== | ||
| + | |||
| + | Parts in [[bukobot-parts-list#x-end-right-idle|bag 16]]. (Your Z slide parts may be different than shown here at the right; you don't need those right now, so don't worry about them.) | ||
| {{wiki:jitsbuild:x-right-kit.png?800}} | {{wiki:jitsbuild:x-right-kit.png?800}} | ||
| - | Clean up this part as before, including the two small holes for the Z slide screws. | + | =====Clean Part===== |
| + | |||
| + | Clean up this part as before, including the two small holes for the Z slide screws (3 mm). (If you were an early adopter, you may have four small holes instead.) | ||
| + | |||
| + | =====Add Parts===== | ||
| - | Add a few more parts from the synchromesh cable kit (bag 11): | + | Add a few more parts from the synchromesh cable kit ([[bukobot-parts-list#synchromesh-cable-system|bag 11]]): |
| {{wiki:jitsbuild:x-right-subassembly1.png?800}} | {{wiki:jitsbuild:x-right-subassembly1.png?800}} | ||
| Line 21: | Line 29: | ||
| Tighten the M8 bolt, not too tight. Then set this assembly aside, along with its Z-slide sub-kit. | Tighten the M8 bolt, not too tight. Then set this assembly aside, along with its Z-slide sub-kit. | ||
| - | [[jitsbuild-y-backend|Next: Y back end]] | + | [[jitsbuild-x-leftend|Prev: X left end]] < [[jitsbuild| Up to Jitsbuild]] > [[jitsbuild-y-backend|Next: Y back end]] |
| - | //The contents of this page may be re-used under any of the following licenses: The [[http://creativecommons.org/licenses/by-sa/3.0/|Creative Commons Attribution-ShareAlike 3.0 Unported License (CC BY-SA 3.0)]], or the [[http://www.gnu.org/copyleft/fdl.html|GNU Free Documentation License (GFDL, version 1.2 or later)]].// | + | //The contents of this page may be re-used under any of the following licenses: The [[http://creativecommons.org/licenses/by-sa/3.0/|Creative Commons Attribution-ShareAlike 3.0 Unported License (CC BY-SA 3.0)]], or the [[http://www.gnu.org/copyleft/fdl.html|GNU Free Documentation License (GFDL, version 1.2 or later)]]. Nothing on any of these pages is there to tell you what to do, only what other people have already done.// |
jitsbuild-x-rightend.1354659871.txt.gz · Last modified: 2012/12/04 16:24 by jit
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 3.0 Unported
