jitsbuild-y-frontend
|
jitsbuild-y-frontend [2012/11/16 19:39] jit |
jitsbuild-y-frontend [2014/01/25 17:41] (current) jit |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| - | ===jit's build: Y front end=== | + | ======jit's build: Y front end====== |
| - | (Go back up to [[jitsbuild|jit's build]]) | + | [[jitsbuild-y-backend|Prev: Y back end]] < [[jitsbuild| Up to Jitsbuild]] > [[jitsbuild-y-carriage|Next: Y carriage]] |
| - | {{wiki:jitsbuild:y-frontend-kit.png}} | + | //This page pertains to the Bukobot v1. Some portions may be useful to v2 owners. For more information, see [[jitsbuild|here]].// |
| - | The items at the top come from the synchromesh cable kit. | + | =====Parts===== |
| - | Not shown in the image above: the Y axis foot. See the last image below for that. | + | Parts in [[bukobot-parts-list#y-end-front-idle|bag 13]]. |
| + | |||
| + | {{wiki:jitsbuild:y-frontend-kit.png?800}} | ||
| + | |||
| + | The items at the top come from the synchromesh cable kit ([[bukobot-parts-list#synchromesh-cable-system|bag 11]]). | ||
| + | |||
| + | Not shown in the image above: the Y axis foot. See the last image below or [[bukobot-parts-list##y-end-front-idle|here]] for that. | ||
| + | |||
| + | =====Clean Part===== | ||
| Start by cleaning up the large printed plastic part. | Start by cleaning up the large printed plastic part. | ||
| As with the Y back end, check that the screws and nuts fit. Also widen the two large holes in the Y axis foot if necessary. | As with the Y back end, check that the screws and nuts fit. Also widen the two large holes in the Y axis foot if necessary. | ||
| + | |||
| + | =====Assemble Part===== | ||
| Assemble as shown: | Assemble as shown: | ||
| Line 19: | Line 29: | ||
| {{wiki:jitsbuild:y-frontend-topview.png}} | {{wiki:jitsbuild:y-frontend-topview.png}} | ||
| - | The lip on the idler ring is on the bottom. The big washer goes under the bearing. You might actually need two washers there, but this can wait until a later step. | + | The lip or flange on the idler ring is on the bottom. The big washer goes under the bearing. You might actually need two washers there, but this can wait until a later step. |
| Bottom view, showing the Y axis foot: | Bottom view, showing the Y axis foot: | ||
| - | {{wiki:jitsbuild:y-frontend-bottomview.png}} | + | {{wiki:jitsbuild:y-frontend-bottomview.png?800}} |
| - | [[jitsbuild-y-carriage|Next: Y carriage]] | + | [[jitsbuild-y-backend|Prev: Y back end]] < [[jitsbuild| Up to Jitsbuild]] > [[jitsbuild-y-carriage|Next: Y carriage]] |
| - | //The contents of this page may be re-used under any of the following licenses: The [[http://creativecommons.org/licenses/by-sa/3.0/|Creative Commons Attribution-ShareAlike 3.0 Unported License (CC BY-SA 3.0)]], or the [[http://www.gnu.org/copyleft/fdl.html|GNU Free Documentation License (GFDL, version 1.2 or later)]].// | + | //The contents of this page may be re-used under any of the following licenses: The [[http://creativecommons.org/licenses/by-sa/3.0/|Creative Commons Attribution-ShareAlike 3.0 Unported License (CC BY-SA 3.0)]], or the [[http://www.gnu.org/copyleft/fdl.html|GNU Free Documentation License (GFDL, version 1.2 or later)]]. Nothing on any of these pages is there to tell you what to do, only what other people have already done.// |
jitsbuild-y-frontend.1353116368.txt.gz · Last modified: 2012/11/16 19:39 by jit
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 3.0 Unported
